Dans KL SE project
-
mmm i would but i drive anything until its dead lol im still driving wes even though its running half power lol
i dont think it would cause any major problems by running it but i might be totaly wrong
-
gives me an excuse to 2.5 it ;) might have to borrow an engine crane from someone lol
-
most tool hire places do them
-
Has it only just started miss firing or was it doing it when you bought it?
-
Have you tried just tightening up the valve cover a bit? Though not too much, they're skinny and will shear easily enough. Or you could take it off, dry it off around the seal, fire a bead of liquid gasket on it if it's just a stop gap. If you're not getting spark - you lose power, economy and may wash the bores as the petrol builds up.
-
it only started yesterday after a 25 mile drive, stopped for a bite to eat and once i fired it up again its run rough since. liquid gasket… sounds like a plan. i wanna get a 2.5 in as quick as possible so no point in oaying out for a gasket that i am going to throw away very soon. thanks for your help guys. i will try tightening the cover up.
-
Good to see you back in a '3 daniel :D
Bit of TLC will have her lookin spankin again, and look forward to seeing
what you do with her 8)
-
@0670f8eca0=youdirtyfox:
Good to see you back in a '3 daniel :D
Bit of TLC will have her lookin spankin again, and look forward to seeing
what you do with her 8)Thanks mate, got alot of plans for her but money is tight so it will be a slow project. white paint and a 2.5 DE are top of the list :twisted:
-
ok, its not been a good day for the SE. managed to get the spark plugs that were covered with oil out, cleaned the holes and plugs and HT leads up. took it for a spin and exactly the same. checked all other plugs and the middle one at the back of the engine was caked! GRRR!!! I was going to replace the front (or is it left?) rocker cover gasket tomorrow but dont think i will bother now. anyone selling a cheap V6 probe/mx6? lol
by the way, if anyone is interested, euro car parts have a rocker gasket for £7.08 inc VAT. kevin coopers wanted £41 + VAT :shock: I have ordered one but may keep it in case the DE decides to go down the same route.
-
one more question, will the DE driveshafts fit the mazda as mine are knocking like a bitch :( think i bought a bit of a shed lol
-
if it keeps dying like that check the leads at night see if sparks are coming off them as you wont see it in the day, if so new set of leads required, also check all the leads on the long ends that go onto the plugs, I had one that cracked down the side and the car would barely run until I changed it
-
@1a2326383f=djmarcopolo:
if it keeps dying like that check the leads at night see if sparks are coming off them as you wont see it in the day, if so new set of leads required, also check all the leads on the long ends that go onto the plugs, I had one that cracked down the side and the car would barely run until I changed it
Thanks mate, will have a look tonight. I have cleaned out all the plugs (fired up the engine while each one was out individually to get any excess oil out) and its still missing. and the front of my car is now covered in oil :( lol
-
What's the cap and rotor like?
-
I have no idea lol. i dont know a good one from a bad one.
-
I have a brand spankers set of leads if required, and brand new cap + rotor if they fit yours :wink:
-
I can get a KLDE engine delivered with under 100k foe about £250 but without ECU and probably wouldnt be here until the weekend. and i still need driveshafts. am i better off just buying a probe if the shafts fit?
-
good one looks clean with clean metal contacts, bad one looks worn away and sometimes almost furry with corrosion.
-
@e65b764943=Marco:
good one looks clean with clean metal contacts, bad one looks worn away and sometimes almost furry with corrosion.
also check the cap and plastic on the distributer for cracks, that can let the leccy run all over the show and cause a misfire, only a couple of bolts hold the whole lot in, easy to remove :wink:
-
dont worry DJ, you were right in the first place. the plug on lead no 6 has a massive split in it about 3/4 the length of the plug! :shock: is there a temporary fix i can do? i dont think electrical tape will hold up with the heat lol. how much for the leads mate, i'll have a lil look on ebay quickly
-
I can do you the leads for £25 inc P&P, if that plastic is split that goes into the head then that causes major probs with running
I will PM my paypal over and get them posted tomorrow if you want
