Hector's - KLZE Turbo Project



  • yeah the ecu (probinator chipped ecu) Will handle around 4lbs of boost with a walbro fuel pump, fmu and afpr.

    I will be running megasquirt. That one Ill get next week but not bolt on yet.

    Also today what i did.

    Figured out intercooler piping and cut the fender well where the cai usually goes. Ill be using 2.0 piping from turbo to intercooler, and 2.0 to 2.5 coupler and then to 2.5 piping to the tb.

    Ill be intercooled @ 4 psi for a few weeks, When I get my megasquirt and figure it out ill install it along with some millenia injectors.

    I got a wideband to tune of course.

    Ill tackle the cross member over the weekend.



  • Ok almost done. I am currently tackling the cross member task.

    FMU AFPR are all connected. So is boost gauge and wideband bung is done.

    Gonna change the couplers i believe. The black ones seem pretty thick tho.


  • admin

    Nearly there then :)

    Does the BOV fit well over the turbo like that?

    Get some samco silicone ones, they are pretty good from what I hear.

    Did you turn the cold side of the turbo to face down?

    Cant wait to see it running

    Jono



  • Im almost done, ill post tomorrow. Yes I did replace the black coupler with a good one. More room. The bov doesnt touch the turbo. I did turn it the other way around tho. I clocked the turbo to the front so that it will connect with the intercooler.

    Ill post pics :) almost done. The cross member was a bit tricky but its getting there.



  • Ok its ready to go. I just need for it to stop raining so i can start her. The oil line is feady too, just havent connected.

    cross member looks cheap, its not.. its very stury and strong.

    here is the oil line and you can see the intercooler.

    and last

    Ill post a video of the start up.



  • Ok im done sorta…

    I had problems reading boost but that was because the intercooler hose was coming off. Got that resolved. My intercooler is way to low, ill move it a bit up.

    It goes to 5 psi :S i only want 4.

    Also I will NOT drive it.. its to lean. At idle im at 11. But as i drive off at 3 k rpms im at 14 and higher 16 :S OW ...

    so yeah walbro is a MUST .

    It runs way nice compared to stock but still i wont drive it.

    The car ran without a fan for a good 6 - 7 minutes running at night with cool air. Didnt overheat at all. Engine is not hot to the touch. bov works fine. Turbo seems fine.. there was oil in the outlet just a bit.. maybe its a bad turbo.

    Doesnt smoke at all. my down pipe is cut, ill weld it next week. It spools NICE.. but its way to lean. So yes I know everyone told me.. YOU NEED AT LEAST a WALBRO.. and I bet even with that.. at high rpms we will be leaning out. One i actually went 17! . :S def wont be driving the car at all until i get the pump in there.

    Ill post a short vid tomorrow.



  • ok
    video

    http://www.youtube.com/watch?v=um1EubTxYnA

    Excuse the mess… they are dummy wires.. they used to be for the fans. Only have one fan now. Not sure if the turbo is good.. it had some oil in the bellhousing. Ebay.. figures.. anywho all it needs its a walbro pump.

    Im not driving it. Im moving the itnercooler up, its to low.

    Wideband rewads lean because its cold, when it warms it reads 10 at idge which is to rich. Causes car to die at idle. I did adjust it and its driveable but i cant floor it or it will lean out.


  • admin

    Good work dude,

    Watching that makes me wana get a loan to do mine :( lol

    Jono



  • me too would love to slap a turbo on mine, would b a laugh in mind but not in pocket!!!



  • It seems the ebay turbo is not of good quality LOL I kinda knew it from the start… I got a back up one from a friend. The oil seals on the exhaust side seem to leak into the downpipe a bit.



  • Ok guys .. finally a video.. Im almost done with phase 1 which is tune it for 5 psi.

    http://www.youtube.com/watch?v=_BugLULEkVU

    Sorry its a bad video.. I didnt have my afs correct.

    I have one problem… My af rations seem to want to hang at 12.2 - 13.5 at WOT. Supposed to be around 12 and no more than 13. At idle i am super rich.. like 10. I suspect an incorrectly set tps mox with idel air screw. Also my fmu was not gettign enough vac. The turbo itself is good. no play and doesnt burn oil.

    Ill try to get another vid tomorrow. Walbro pump is installed.

    I started to read on my megasquirt and will begin install once I get the millenia injectors.

    By the way the car pulls LIKE crazy all the way trough 6 k rpms. I dont take it any higher as i need to properly tune it.

    I have not replaced the plugs which can cause them to heat up and detonation can occur.

    The car is now driveable, Yesterday I drove for whole 2 hrs. I know understand the turbo concept.. usually at normal driving you arent really at boost. When you want to get boost all you do is floor it.

    Kinda like nitrous but the power is always there.

    I drove today for anoter hour and back. Drives fine like any other car.

    One problem i got its that it dies at idle, i need to adjust the tps and idle air screw and possibly change the spark plugs. af at idle is 10.

    afpr is set to 50 psi. fmu is a 12.1.

    Ill post more pics and vids soon.



  • awh man love that noise! How much has it costed you all together so far? I gave you 5 ;) (for the setup not the camera work :P )



  • It costed like 700 You get what you pay for tho.. the turbo seals seem bad. Smoke comes out the exhaust pipe. Took out the plugs to gap them and theres no oil in there. The turbo housing has little oil. Im sure its the exhaust side seals. I had stock 45 gap and at high rpms it was blowing up… was nasty,, gapped the plugs to 30 and its all good. All i need to get well is anoither turbo.. this one will be ok for daily driving.



  • where did you get the piller mounted gage pod



  • –-

    UPDATE
    Im done, ill post a vid on thursday.



  • heres a video

    http://www.youtube.com/watch?v=AE6jtIJYaPU

    also its smoking on start up..seels like oil is getting past the dynamic oil seals.. bleh.. i need a real turbo.



  • it's gettin fast hector ..
    You can almost beat me … :)
    My K8 is from hell :roll: :twisted: :lol:

    Got to get me a KLZE :D



  • whys everone going mental over the klze conversion its a easy conversion..

    Get Dropping Different engines in.



  • Welly, that could be , if you live somewhere with easy access to the KLZE engines…
    i live in Portugal, can you send a engine to my house ? I can only order a KLZE from the netherlands, so ...



  • ok an update. I was able to kidna run it right…

    at idle ill be like at 12 , at cruising ill be like at 14 and under boost ill be around 11.2 - 11.9 NICE

    its a HUGE power difference..

    Now why was i running crappy? well the fmu wasnt even connected to boost/vac.. and my afpr was set to like 50 psi!

    Ok.. connected the fmu.. and it went WAY rich.. 10 at idle and 10 under boost..

    I lowered the afpr to 30.. still ran a bit rich at idle.. wtf..

    i know .. but well..

    lowered to like 15 psi at idle and it idles perfect. Cruises perfect.

    Apparently the millenia s injectors make a HUGE difference.. i wonder what the afs would be if the stock fpr was there...isnt that like 35 psi or something?

    anywho like i said, the wideband reads nice and rich under boost, nice and lean under regular cruise (not to lean or rich) an at idle its sorta there. My fuel mileage went from like 12 - 15 mog to around 20 -22 mph.

    The car will no longer idle fluctiate.

    Clutch does not slip at all under normal driving conditions, under boost it will a bit.

    I got a replacement act clutch now :D

    ill try to make a vid in the weekend.


 

Copyright 2021 UK-MX3.com | Powered by NodeBB