Sooty 2.0 - Autozam AZ-3 B5ZE - rear bumper respray



  • looking good as always :cheers:



  • looking really good marco. tidier than mine. i'll have to meet up some time with you and check over my example, not as tidy as yours mind.

    once i get my cooling pws pipe i shall have her back on the road, though need to adjust the ile as she sits at 1500 rpm, then when you put her into 1st it drops to 800 rpm. not sure what might be going on. might need a new clutch at some future point, need to dbl clutch for reverse sometimes.



  • Thanks Edy, would be nice to see yours updated ;)

    Thanks Foxy, looks decent in photos but a nightmare to clean and keep scratch free!

    Garfy, I have came close before lol.

    Cheers DJ :cheers:

    Spoddy, for sure! Hmm maybe ecu using neutral switch to change the revs. Reverse is straight cut gears so don't be surprised if it's awkward sometimes :)



  • I decided the worst looking part of my car was the rear bumper. It came with the car pretty hammered with minor collision damage. Fortunately nothing frame bendingly serious.

    Rough old bumper, dented and apparently painted with dulux with a yard brush, also rubber "I can't park strips":


    The 'new' bumper from a certain scrap car. Had to be rubbed back down to plastic due to silicone inclusions on the last persons respray.

    Rusty bracketry

    Loose rust off

    Dipped in magical green liquid:

    Dererusted and acid etch primed, later 2k painted:

    Worst bit of the cars rear:

    Quick 2k new paint on the rear panel:

    Shiny HKS and new paint :D



  • I like!

    Nice work.



  • Great stuff dude, slowly but surely getting mint :-p



  • I'm left with no excuses,Marco. :? Even in weather like this you still managing to do awesome and great jobs :respect: i will make a small update a bit later..



  • how are your rear wheel arches marc, mine went due to chips and water getting in and bubbling the area near the bumper and under the fuel cap.
    so i rubbed the paint off and had to rub alot of rust off. made a few holes as metal got that thin under the fuel cap area. also had to build up the rear drivers side with some metal and filler until i get it done properly.

    some cheapo black pound store spray paint to blend in, but looks much better than bubbly paint. i do have the bottom corner of the passenger door bending out slightly as it has rusted away from the seam. its the area in front of the side skirt. so i would need a passenger door in black if you know of one.



  • Wee update. Did this months ago but sure. GENUINE MAZDASPEED YOOOOOOO


    Had a bit of fibreglass work to do. Also filled in the badly placed number plate screws in favour of the real holes which use m6 bolts. Back garden spray in 2k. Also had to make room for the IC behind the support, wasn't willing to chop up this bumper in any form! Fitment is fantastic.



  • I want that bumper…... Nice work mate



  • That bumper looks class!!! You always doing great job on your car. I may drop mine in for your back garden spray painting, lol.



  • Thanks guys! It's all in the wet sanding and DA polishing!


  • admin

    Looking good Marco!

    How easy was it come by that Mazdaspeed bumper? I'm still wondering if I want to go down that route, they do look great though!

    Jono



  • Difficult jono. There are replica bumpers about but I've never seen a mazdaspeed one for sale.



  • What primer you using,Marco? And what paint? I'm thinking to go by 2k supergloss .



  • I use the upol high 5 looks like this: http://www.smartexpress.co.uk/products/Aerosol-U%2dPol-High-5-Light-Grey-Primer.html

    2k solid, make sure you've a mask that is appropriate, 2k is nasty nasty stuff!

    MS bumpers are super rare, there are a good few reps in US/Can but they're not as good fitment as the real deal. I love them <3



  • Some other updates I forgot to add:

    Upgraded to a proper variable TPS using an automatic BP throttle body. This gives far more linear response and accuracy for megasquirt :)



    And a cheap unused K&N for Mr snail:

    I rebuilt a rear caliper, it was quite a chore cleaning it up! It was starting to wear grooves in my discs so was due new seals etc.


    Also changed the cam cover gasket as the generic brand one failed after about 9 months use. Mazda OEM FTW!

    Still looking clean under there:

    Been working on this for a few days, only passenger side done:



    Rx-7 FD seat in an Mx-3, horrible task as the mx3 rails are at different heights, spacings, angles etc! Took many many hours of drilling, grinding and welding. Super comfortable, love these seats!



  • About time I did an update. Car has been running well. Swapped in my Walboro 255, improved 3rd 4th AFRs, but did reveal how it starves with less that half a tank :?

    Annual testing:

    Got my custom evo8 manifold skimmed flat, no more leaking :)

    Current big project: OEM JDM LSD swap from v6 to i4 G series box.

    Ring gear fun

    'bout flipping time…

    mmm

    helical


    ARP bolts and nuts


    Only identifying numbers:

    A beautiful sight:

    So the box is all bolted up. Just getting axles ready then it's time to slip the engine out and tidy things up.


 

Copyright 2021 UK-MX3.com | Powered by NodeBB