DJMARCOPOLO'S - The GREEN RIVET



  • noice bling 8)



  • Thanks, was thinking of wrapping it in heat shield when fitting it but then I do like shiny metal



  • DJ, Has someone put a big F U on the back of your car?



  • @8ffcaa1bf1=djmarcopolo:

    Thanks, was thinking of wrapping it in heat shield when fitting it but then I do like shiny metal

    me too! wouldnt do it mate, you wont be able to see it change colour :D



  • Very nice material 8)
    The headers I ordered from ebay.co.uk didnt fit well. Had to cut one of the two pipes because it was to tight with the "bar" from the gearbox and align it right and weld again. I did a custom exhaust at the same time so I dont know about the length though.

    But why chrome altezzas? The stock ones doesent look so bad? :o



  • @99d91e701f=unclegreg:

    But why chrome altezzas? The stock ones doesent look so bad? :o

    The headers I have had a good plan with to get them right :wink:

    The altezza's I have black ones that look great but they leak like a cheap nappy (diaper) and were always steamed up, so I bought those cheap the only reason being is I have quad rear lights with twin fogs wired in mine and you can only do that with altezzas as the standards dont have the extra hole on the left side of the car for a bulb



  • YAHOO - 12 months MOT as from today

    One advisory and that is the clip that sealss the drive shaft gaitor has dropped off which is a 5 min job, not bad for a car I bought as a scrap non runner for £90 nearly 17 months ago.

    I did new rear brakes last month as I found a caliper had seized again but she has a perfect bill of health :D :D :D

    I also did some bits the weekend so you may notice I have changed something on the front last week :P



  • good time to start on that ze now then!, that will give you a year to fine tune it and hopefully get emmisions right!.



  • lookin good bud…

    Where'd ya get the front plate made up? Lookin to get a square plate for mine too...



  • @8a22ebf562=Garfy1981:

    good time to start on that ze now then!, that will give you a year to fine tune it and hopefully get emmisions right!.

    KLZE FITTING DATE = 16+17tH APRIL 2011 :D :D :D

    The Emmisions will be ok as I will be remaking the exhaust so the cat can be refitted and my new decat fitted as well



  • Nice one :)

    Looking forward to this.



  • If you run into any trouble give me a shout.



  • @8bfb291ce0=ukmx3admin:

    If you run into any trouble give me a shout.

    If its as straight forward as you explained on the phone it should be fine, its not the first mx that I have had the engine out of.
    I am considering removing the EGR but if everything else is done on this engine and its a straight swap I will be fine hopefully, if not I will be riding my bike a lot and going to japfest in a skoda octavia :cry: .

    Before it goes in, its a full service, decent oil ( any recommendations on that please) bosch super 4 plugs then the induction kit + kerr nelson leads

    Will my old K8 airflow sensor be ok thats fitted in the induction already or will I need an MX6 one ???

    I am praying the exhaust is not too loud, I am fitting the race headers and downpipe, decatted with a 2.5" straight through exhaust into a 5" tailpipe and oversize rear box



  • K8 VAF (JE50) is fine as its the same as MX6 KLZE, its the KLDE that use different VAF (KL02)



  • Excellent, cant wait to get it in there

    8 DAYS TO GO



  • your be starting it ( 16th ) on my 30th birthday!, im sure it will go fine, ditch the egr system, its not needed on ZE. just requires a bung on mx6 manifolds.

    good luck, i will be offline for a while, so hope to see it finished when i return end of april.



  • Don't forget to paint everything you want to before the swap as its a pain afterwards.



  • @e9b25c29fc=ukmx3admin:

    Don't forget to paint everything you want to before the swap as its a pain afterwards.

    I like the black top, have been buying loads of little bits, will be wrapping the rear manifold and all of the downpipe in ceramic tape to transfer the heat out of the engine bay, just going to order some oil and then its all ready to go next week.

    Today as I had some spare time at work, sprayed the calipers up and gave her a good polish after leaving it to get dirty for the winter



  • ware did u get the headers? thinking about getting my old mx3 back and wanted to do this :P



  • @ed71c0c694=DaveMc:

    ware did u get the headers? thinking about getting my old mx3 back and wanted to do this :P

    Toyo sports in birmingham make them for the MX6 for £127 delivered, they are going to change the design of their mx6 ones for the mx3 once I have sent them photos of them fitted to mine and the measurements for adjustment to make it fit, the easiest way to make them fit is to just extend the downpipe and turn them into downpipe and decat all in one but then you get trouble with emissions on later cars

    I will show them photos of it all and get the downpipe shortened enough so you can still use a standard cat, its not that hard for them to change the design and shorten the length of the downpipe before the flexi.

    I will keep you posted on here, otherwise buy a set and cut down a decat pipe to suit it


 

Copyright 2021 UK-MX3.com | Powered by NodeBB