HammyGlos MX-3 Project (OEM+!)
-
@984a999745=djmarcopolo:
Nice job, will see it in its glory tomorrow :D
Thanks DJ… And yes tomorrow it will get a proper run in... :wink: :lol:
-
they wont be so shiny when you get down here :(
All good for tomorrow, weather looks great for it, just remember to bring everything and just call my dad when you get into Hamble he will get you in past security or drive up to the gate and tell him you are there to meet Keith and he should let you in :D
-
Looks rather tasty :)
-
@f864d55672=djmarcopolo:
they wont be so shiny when you get down here :(
I don't reckon any of the car will be shining by the time i get down to you tomorrow :(
But hey… Sunday job (if it's not too cold) can be to clean it... although i'm going to manchester next weekend.. so maybe i'll just leave it dirty for a week.
-
ahh top secret mx3 meet i see. :D hush hush !!
love the exhaust btw.
-
@fa66491c95=Garfy1981:
ahh top secret mx3 meet i see. :D hush hush !!
love the exhaust btw.
Cambelt fitting meet :D
-
CAI from Probestore is finally in the post… Waited since November... but soon it will be in my grubby mits!!! :D
-
CAI arrived today… a bit lost on how to fit it properly tho....:roll:
help???? :lol:
-
Simples, go on my project log, page 5, about halfway down there is a picture of my one fitted, I bought mine from probestore too. You will have to locate yours in the gap to the left of where mine is located as I have moved my washer bottle
-
Cheers Gulfy…
So, do i need to keep the concertina bit or was that for you to reach the spot where you placed your filter?
-
you need to set it up pipe-wise exactly as I have, stock concertina pipe - VAF - CAI, my concertina pipe is pulling that way so I can stick filter down that hole!
-
Thanks bud…
I'll look at doing that this evening if it stays dry.
-
It's been a while ince i updated this..
Notmuch to show right now… but...
I have "Yellow" Lights on the front... pic not great.. will try another when it's a bit darker...
Also new square plate fitted…
Thats all for now…
-
lights look spot on, do they improve night vision?
Got to say though, square plate needs be on the side…
looks better and you wont be covering your rad :wink:
-
Thanks… I think they do improve night vision... not by a whole lot.. but enough to make a difference.
The plate is staying in the middle until such times as the holes get covered :wink:
-
all road legal too?
Ah I see, you have plans :)
-
@175690e32c=youdirtyfox:
all road legal too?
Ah I see, you have plans :)
Yeah Matey.. All road legal and MOT Friendly!!!
I do indeed have plans… Although, these plans are constrained by cost, therefore all progress will be slow :cry:
Hoping to have some done for Japfest... :wink:
-
So since the weather is nice…
I have started to rub down a bumper with the plan to delete the standard number plate holes....
1st pics.. i'll be doing this on and off... so do expect any over night surprises!! :lol: :lol:
Hope to get it all rubbed down, filled and primed by next week…
-
Rear Cam Cover Painted This Evening…
New IM Gaskets…
OLD IM Gaskets vs NEW IM Gaskets
Finally…
I had an issue with No. 5 Spark... Lead melted...
Pic of all old bits.. in the middle is the part of the Spark Lead :(
-
Radiator Panel Now also Matt Black
Oh…And the car is up and running again!!! :D