Garfy1981's - KLZE Project superleggera



  • hello, due to a couple of requests here is lifters;

    make, Powerlift Autospezialteile Bonrath ( German ) www.bonrath.com/e/pl.htm , was told that these were for opel corsa ( although corsa i think was nova abroad? so not sure if its nova or corsa)
    Im sure that in any doubt any style of lifter would work, as these were just laying around in local modification store. www.trac-art.co.uk

    Any how
    Length of lifter fully extended; 430mm
    From tip of wing by headlight to centre of bottom fixing ( wing ) 485mm
    From centre of fixing to end of bonnet over headlight 765mm measured straight not against curve of bonnet.
    ( hope these measurments arnt too confusing. )



  • well its been exactely one year since i put the mx away to save some cash to fix up the project house. Started getting a few bits cleaned slowly, removed number plate holder and old plate, looking for a legal smaller version now, without number plate holder. Also received a nice parcel this morning any one care to guess what it is???. :D

    going to sell my blitz sus filter even tho i dont want to, but its too big to relocate. Now looking for a good quality ( ie not ebay ) replacement. Relocating as barrywhite and gulf mx3 have into front well.



  • Come on garfy spill the beans! What is it?? Looks like some sort of ECU, can't work out the lead though, looks like an old printer lead LOL! What I wanna know is, is it gonna make your KLZE quicker? if yes I definately need to know!!!! LOL :lol:



  • Well i hope so lol, its megasquirt stand alone ecu. Will remove the Kl36 and install megasquirt, can then remove the VAF ( which removing that alone should free up some hp! ) a small IAT sensor goes in its place.
    Dyno tune everything up and hopefully free up some Hp. Dont know when it will be installed as im still looking for a AEM UEGO AFR guage to monitor the air fuel ratios.
    Marco is also using same system but his system is a bit more advanced than mine!!.

    oh sorry guys i have no intention of selling kl36 and je50. Keeping it as a back up fail safe!.



  • Have you got to replace dissy with coil packs?? Would like to go down the stand alone ecu route myself but can't afford/warrant OMEX, and too stupid fo megasuirt, unless a certain someone can help :wink: Looking forward to japfest to see everyones cars and faces etc…........

    Whats the megasquirt setup gonna cost in total if you don't mind me asking?



  • Trust me mate I'm not megasquirt smart either I brought it for whole issue of plug and play. My system should use stock dizzy. Marco is running coil packs which do give greater control but I can upgrade to that at a later date. The set was 400 dollars shipped. I didn't want to spend too much as i'd rather have a LSD if the two were closely priced.

    Looking forward to japfest too! :-)





  • hmm i like the look at that. how much was it garfy?



  • bad news!!!, years worth of sitting has left polished manifold looking very sorry for itself, two hours of megaris and buffing later still not looking good!, to the point where i dont even want to take it to japfest now!!, hoping i can find a powder coaters to do a fast turn around job. Otherwise its going to look pants!!.

    Hate damm polished manifold now!!, takes too much tlc to keep it looking nice!, just want it sprayed and i can just wash engine bay and end of!!.

    Dont want to spray it myself in situ, rather is was pro done.

    watch this space i guess!!. :(



  • i want one megasquirt that is



  • To Do for 2010-2011.

    Right decided to set myself a little realistic list for works for up coming year, havent really done much to mx over last two years due to a number of factors, buying flat, having baby, buying house, recession, getting married… list is endless and poor car just sat there waiting patiently for some attention.

    So her goes....... not in order btw

    Corksport front strut brace.
    fitment of aem uego guage
    2.5 mx6 gearbox c/w quaife LSD.
    fit megasquirt and dyno tune.
    fit HOPEFULLY ( still no updates. :( ) lexan rear glass screen
    purchase and fit full set of performance bushes from mx3.com wysbishops group buy.
    Complately remove dash, and re vamp, with the 1990s gloss style of top half being flocked. Remove part centre console and fit custom carbon fibre plate housing dials. Radio removed.
    Remove door cards and fit custom carbon fibre sheets, c/w custom e/w window control switches. Possibly relocate into centre carbon fibre panel?.
    Remove speakers.

    Induction kit relocation/alterations.

    Towards end of 2011 strip interior, custom roll cage to finish handling upgrades. Re trim carpets for kinda porche gt3 rs styling. Going for that stripped out but stylishly done look!! hopefully :?

    Must do for may 2011 MOT refirb corroded rear brakes.

    Full service, usual expensive oil, plugs, filter etc.

    early 2012 aim, lightweight 17 inch alloys, decent branded bucket seats/harness.
    hopefully stumble across a caron fibre bonnet and mazdaspeed front bumper on ebay.uk but very much doubt it lol!!

    well watch this space i guess!!!!!



  • http://www.youtube.com/watch?v=Ru7ZvukLCqI

    started after months of sitting still, just need to clean it now !!.



  • Inspired by Keith i went outside for a couple of hours to finish what i started towards end of summer and that was to strip the sound proof bitumen out.
    In summer i stripped the interior completely, apart from dash to start rebuilding interior to something a bit more my taste :)
    Its amazing how many parts have come out and the weight drop must be huge, together with polycarb rear screen i hope to get it below 1 ton. (metric). There was 9kg of bitumen and even the weight simple things like a gear knob is surprising.!.

    Heres pics so far, ive still got to clean up the last of the bitumen, then may try and get dash out so interior can be resprayed and then re built.

    oh i still havent started engine since May :(



  • Love the sound of your interior mod. list should look mighty fine!



  • Not much to report. Started it last week, turned over nicely.
    Engine is corroded badly now :( it nothing like its glory days in 2005 !.
    Almost got dash out. Is being a right james blunt !.
    Also de springs arrived from u.s. very happy with quality. Will keep them stored ready for next years engine re build.



  • Update,
    Full cage almost done, just front section left, sunroof motor removed and roof now welded shut,
    AEM guage nearly in, poly carb rear screen nearly in.
    Dash still to prep and re install.



  • Nice to see people starting to work on them again bud, and I do love the look of that cage..



  • Nice work on the cage, did you design it yourself?



  • The cage is not my design, but a sort of come from discussions that I wanted a functional cage rather than something that just looks.
    The value of it won't be cheap once it's done tho!.



  • Just make sure you have got some X's above your head!!

    I just had a hoop above the windscreen linked to a rear like yours at the corners and in the middle, but nothing above my head.

    Its been about 3.5 years since my crash and i'm still not fully better (if I ever will be).

    I'd give anything if I could turn back time and put some crosses / diagonals above my head!! anything!!


 

Copyright 2021 UK-MX3.com | Powered by NodeBB