Barrys Project
-
yeh my rear seat belts are out only coz the studs on top of the ksports were shorter than tanderd shocks i couldent fit the strut brace and seat belts on them so the strut brace won and i lost rear seatbelts
-
Began the stripping process today and not sure how far im gonn go with it, but i can tell you i have managed to remove around 28kg so the luggage scales say.
here is what was removed:
and here is inside the car now:
Still need to change all brake pads, paint calipers and paint and fit the new FAKE JDM lip :lol: :lol:
Who cares!!!
-
looks like you had a strut brace welded in
and then cut out agen
-
How much for the boot plastics? I'm just outside Chester so can prob pick them up depending where in Cheshire you are, PM me your post code.
-
Also the best types of weight to lose are ROTATIONAL MASS and UNSPRUNG weight.
So a fidenza flywheel would be a great place to shed weight, then a set of ultra lightweight alloys, you can even get lightweight tyres anf fill them with lightweight gas!!
Lightweight pullys, underdrive your auxilleries, can you get a lighter weight clutch assembly (padle type perhaps)
Get the crank lightened and balanced.
Lightweight coilovers
Then look for heavy things, remove aircon, remove heater and heater matrix ( perhaps not in this country though), swap glass for some form of plastic, CF hood, fiberglass Z3 front wings, light weight battery.
Go on a diet, LOL
I'd do all this before I got to removing my seats
-
@bb65ebfe1b=james:
looks like you had a strut brace welded in
and then cut out agenI welded a solid bar in ages ago to mount my harnesses too. Worked pretty well but harnesses for every day use are a pain in the ass so cut it out.
-
Not selling any bits sorry, also it was 45kg i removed not 28. Can feel the difference in throttle responce straight away. Its not even that much louder but i can imagine a long motorway drive could be annoying. Also i have thought about a carbon bonnet but its just the cost and i would like to remove some more weight from the front anyway.
-
wow, thats an amazing shed of weight gone!. Get rid of your roof motor and prob get it over 50kg.
Is this your daily driver?
I havent forgot about tailgate, im on the case from tuesday!.
-
yeh this is my daily driver and it really isnt too loud, but thanks i wanna get 50kg off it already feels loads faster with that gone :D
-
So over the long weekend i did a few things:
Changed all the brake pads and loosened up and greased the rear calipers as they were a bit stiff. Put some EBC NO-STUFF (Ultimax) to give them a try as they are quite cheap :D only just gripping properly now but they seem ok.
Also removed the old intake setup, relocated the overfill bottle and put on the FPS one, but still have to remove the spot and put hole in for the feed. Couple of pics :D
-
very nice…A+
-
How you planning to cut a hole for your air feed? When I did mine, I took front bumper off and used a holesaw, then I trimmed it up using a small cutting disc on a dremmel, then I fibreglassed in a cut down plastic pipe to hole in bumper where the fog light used to be bit of a nightmare job…........
-
@a2abedc464=mx3gulf:
How you planning to cut a hole for your air feed? When I did mine, I took front bumper off and used a holesaw, then I trimmed it up using a small cutting disc on a dremmel, then I fibreglassed in a cut down plastic pipe to hole in bumper where the fog light used to be bit of a nightmare job…........
Well im not quite sure tbh, was just gonna get a dremmel and drill and make a hole then hit up nightstalker to spin up some alu pipe to fit in the hole.
How wide did you make the hole?
-
Can't remember exactly, but it was not a perfect circle LOL. If I remember hole was made a little bit bigger than diameter of fog light hole, think there is a part of front bulkhead to avoid cutting through too
-
@1023f4a856=mx3gulf:
Can't remember exactly, but it was not a perfect circle LOL. If I remember hole was made a little bit bigger than diameter of fog light hole, think there is a part of front bulkhead to avoid cutting through too
Thanks i'll keep that in mind when doing it. Had a quick look last night as i was hoping to take the spot out without removing the bumper but that aint gonaa happen :(
-
@387d058114=barrywhite21:
@387d058114=mx3gulf:
How you planning to cut a hole for your air feed? When I did mine, I took front bumper off and used a holesaw, then I trimmed it up using a small cutting disc on a dremmel, then I fibreglassed in a cut down plastic pipe to hole in bumper where the fog light used to be bit of a nightmare job…........
Well im not quite sure tbh, was just gonna get a dremmel and drill and make a hole then hit up nightstalker to spin up some alu pipe to fit in the hole.
How wide did you make the hole?
Who,lol
I can always make the outer spun flange much larger than nessecary and you could trim it down to fit the hole perfec…
-
@bdbe0d6d61=youdirtyfox:
@bdbe0d6d61=barrywhite21:
@bdbe0d6d61=mx3gulf:
How you planning to cut a hole for your air feed? When I did mine, I took front bumper off and used a holesaw, then I trimmed it up using a small cutting disc on a dremmel, then I fibreglassed in a cut down plastic pipe to hole in bumper where the fog light used to be bit of a nightmare job…........
Well im not quite sure tbh, was just gonna get a dremmel and drill and make a hole then hit up nightstalker to spin up some alu pipe to fit in the hole.
How wide did you make the hole?
Who,lol
I can always make the outer spun flange much larger than nessecary and you could trim it down to fit the hole perfec…
Boll ocks sorry dude!
-
Ok Been a long time since i had any real time or money, i have both of these so have invested in some halo projectors and ive gotta be honest they look great.
Im gonna get them on tonight hopefully and get some more pictures up with them on also point out any issues with whch way the beams point and how to alter it.
-
Just a quick one before you fit them, how easy do you think it would
be to remove the front cover?
-
Look the same as usual, heat up folded over clips and remove, i will double check later for you :)