HELP!! No Reverse after fitting KLZE engine



  • It came out of my car and was working fine when I took it out.

    Has been stood for a few months, but can't see why that would cause any problems.

    If you do end up putting your gearbox in, double check all the clutch gubbins just incase.



  • How do you like the ZE power then? :D its alot of fun.

    They should have fitted them as standard.



  • Definately should have fitted as standard they are amazing



  • Have you thought about taking gearbox off the K8 and sticking that on the ZE? Could save you loads of fault finding time? I know its a biggish job but sometimes…..................



  • we talked about doing that before we put it in as it was daryls k8 gearbox so it may be coming out again next week :roll:



  • do u not need to use differnt engine mounts?

    have u tried putting into gear with the car off and started to see? obviously have the clutch pressed while starting lol

    I had a car with a faulty 1st gear and that was the only way to get into it and work, no fun at lights



  • Its just aluminium high temp paint I used ( so you can get yours painted up to match ) . I'd get it painted just in case.



  • whether the car is running or not clutch in or out I have exactly the same outcome :cry:



  • I read somewhere you have to put a tie through the open diff when removing transporting g series boxes. ? Can't see how that would affect reverse tho? Apart from that I'm stumpted ?, time to try new box :-(

    Congrats and welcome to the world of the ze owners club !



  • I do have the dropping gear lever problem but I now have a new mount to fit this weekend but it never affected it in the old one,
    I will be removing all the linkage and trying the box insitue to make sure it has the reverse gear or I can find it at all direct on the slector otherwise i think it will get a new box on it very soon, but its funny watching the wife push me into the drive everyday but its an arse when i have to go shopping or need to go anywhere



  • Does the MX-3 have a 'lock out' on reverse so that you can't select it when in a forward gear? Could be stuck or something?

    Can't remember if they do or not.



  • dont know will try and find out



  • See these boxes is there an extra ball thing for the rods? A saxo I was working on the day doing a clutch did put it on the wrong one and the gears were fecked

    Has a spare for fuck knows what reason but the other gave it more movement but saying that u can get into 5th so must have enough



  • have you tried putting it into reverse with out the gear stick? take the gear selector rod off and use a large screw driver and put it into the selector hole rotate clockwise and forward



  • PROBLEM SOLVED BY ACCIDENT TODAY

    Today got to work and a huge puddle of oil appeared in under an hour under the car and it stunk so it was obvious it was gearbox oil so lunchtime jacked it up to look where it was coming from and found it was pissing out the reverse light switch, took it out, the copper washer was overtightened and split.
    I put a new copper washer on and bingo reverse gear came back, looks like the switch is so close to the selector inside the gearbox just that extra almost 1mm further in and the switch blocks the reverse selector, big surprise as they are not usually engineered that tightly into the gearbox on most cars, but problem solved now :D :D :D

    Now just tickover and missfire to sort :D :D



  • I ran mine for about a week with no gearbox oil as guys who done engine swap forgot to put oil back in box, no damaged was caused and it's still strong to the day. I had castrol cheap oil in first and I felt very sloppy and old but switched to redline Mt-90 oil and it made a massive difference. ( opie oils )

    Glad it's all fixed !



  • @5f21cb179c=djmarcopolo:

    PROBLEM SOLVED BY ACCIDENT TODAY

    Today got to work and a huge puddle of oil appeared in under an hour under the car and it stunk so it was obvious it was gearbox oil so lunchtime jacked it up to look where it was coming from and found it was pissing out the reverse light switch, took it out, the copper washer was overtightened and split.
    I put a new copper washer on and bingo reverse gear came back, looks like the switch is so close to the selector inside the gearbox just that extra almost 1mm further in and the switch blocks the reverse selector, big surprise as they are not usually engineered that tightly into the gearbox on most cars, but problem solved now :D :D :D

    Now just tickover and missfire to sort :D :D

    Mine misfired at first becouse it was running rediculously lean. Old fuel pump was the problem.. And what whas the tickover again?



  • doesn't the MX-3 use dexron 2 ATF (automatic transmission fluid) even in the manual transmissions?

    Or am I thinking of my old mondeo?

    Anyone got a Chiltons to check?



  • Just dug out my own chiltons.

    Recomends:

    For 1990-1992
    SAE 75w-90 (gl-4 or GL-5) or Dexron 2 ATF for all season protection
    and
    SAE 80w-90 (gl-4 or GL-5) for use in sustained temperatures above -18 (minus) degrees centigrade

    For 1993-1998
    SAE 75w-90 (gl-4 or GL-5) for all season protection
    and
    SAE 80w-90 (gl-4 or GL-5) for use in sustained temperatures above +10 (plus) degrees centigrade



  • Hmm think it must be your ford mumgero that uses ATF we checked the recommended oil on the system of a regular motor factors and they said 75w 90 for MX3+6 so it has some expensive 80w90 in it as thats all i had available at the time

    The misfire I think is due to the timing on the dizzy as we need a timing light and didnt have one, we just timed it by eye so thats on the list to do and the tickover is throttle body temp sensor, will clean friday or replace after my holiday


 

Copyright 2021 UK-MX3.com | Powered by NodeBB