<![CDATA[CV Joints…]]>Anyone done their own??

Any hints and tips???

Wanna do mine this weekend provided i get the ABS rings through in time… Only.. never done 'em before!! :roll:

All advice greatly recieved!!! :wink:

]]>https://www.uk-mx3.com/topic/2016/cv-jointsRSS for NodeTue, 13 Oct 2026 07:05:29 GMTWed, 29 Jun 2011 14:21:25 GMT60<![CDATA[Reply to CV Joints… on Wed, 29 Jun 2011 14:21:25 GMT]]>Anyone done their own??

Any hints and tips???

Wanna do mine this weekend provided i get the ABS rings through in time… Only.. never done 'em before!! :roll:

All advice greatly recieved!!! :wink:

]]>https://www.uk-mx3.com/post/2016https://www.uk-mx3.com/post/2016Wed, 29 Jun 2011 14:21:25 GMT<![CDATA[Reply to CV Joints… on Wed, 29 Jun 2011 16:42:04 GMT]]>it was very easy mate. take wheel off, undo 3 bolts holding braks in place on the wishbone. pull break out of joint after taking the hub nut off and pull the cv joint out. Might need some hard pulling as they can be pretty tight in there. make sure you get the old clip off before you try putting the new one on.

]]>https://www.uk-mx3.com/post/23547https://www.uk-mx3.com/post/23547Wed, 29 Jun 2011 16:42:04 GMT<![CDATA[Reply to CV Joints… on Thu, 30 Jun 2011 09:06:21 GMT]]>@89d89873d4=daniel:

it was very easy mate. take wheel off, undo 3 bolts holding braks in place on the wishbone. pull break out of joint after taking the hub nut off and pull the cv joint out. Might need some hard pulling as they can be pretty tight in there. make sure you get the old clip off before you try putting the new one on.

Sounds so easy… However, Hub nuts are a b***h to remove for a start...

]]>https://www.uk-mx3.com/post/23558https://www.uk-mx3.com/post/23558Thu, 30 Jun 2011 09:06:21 GMT<![CDATA[Reply to CV Joints… on Thu, 30 Jun 2011 09:14:57 GMT]]>I jack it up
Take wheel off
Get someone to stand on the brake in the car (or stick a screwdriver in the vanes of the brake disc and let it stop against the calliper - bad unrecommended way :lol: )
Batter out the notch on the hub nut
Get breaker bar with 32mm socket with extension ~(eg scaffolding) if it hasn't been off in a while
Crack it off
Take off BJ to spindle nut
Then swing spindle enough to get the axle out
Then deal with the messy bit of changing the CV joint
Tighten nut to spec ( some high figure 230nm? ) Then it will be easy next time when you're putting a 2.5 in.

]]>https://www.uk-mx3.com/post/23559https://www.uk-mx3.com/post/23559Thu, 30 Jun 2011 09:14:57 GMT<![CDATA[Reply to CV Joints… on Thu, 30 Jun 2011 09:18:32 GMT]]>@14e66ea3c2=HammyGlos:

@14e66ea3c2=daniel:

it was very easy mate. take wheel off, undo 3 bolts holding braks in place on the wishbone. pull break out of joint after taking the hub nut off and pull the cv joint out. Might need some hard pulling as they can be pretty tight in there. make sure you get the old clip off before you try putting the new one on.

Sounds so easy… However, Hub nuts are a b***h to remove for a start...

yeah i had a high impact air gun on mine :lol:

other than that its not a difficult job

]]>https://www.uk-mx3.com/post/23560https://www.uk-mx3.com/post/23560Thu, 30 Jun 2011 09:18:32 GMT